Zinkspray alu (glanzend) View larger

Zinc spray Alu Gloss


PRO-Paint Zinc spray Alu Gloss is a purpose-designed paint for cold galvanising of iron and steel surfaces, can be used to touch-up and repair damaged areas of altered zinc, for steel parts, bodywork, fencing, metal buildings and heavy industry. This primer provides a tough, corrosion- resistant and protective gloss coating to iron and steel, leaving the surface with a newly-galvanised appearance

More details

Data sheet

Application domain touch-up painting
Product type touch up paint - galvanizing
Application area metallic surface
Volume 500 ml
Packaging Box of 12 cans

More info


Especially for cold galvanising iron and steel constructions, retouching and repair of damaged parts to old and weathered zinc in steel construction, trailer construction, fencing, heavy industry etc. As a primer gives shiny and long-lasting protection against corrosion on iron and steel, and due to the colour fastness lets the treated surface look as ‘fresh’ as galvanised metal. Fast drying, with a strong adhesiveness and excellent for painting over. Temperature resistant up to approx. 250°C.



  • Iron
  • Steel


Product references

  • Excellent cathodic corrosion protection
  • Fast drying
  • Resistant against petrol, chemicals and weather influences Good filling power 
  • Good spot-weldability (observe zinc vapour)
  • Excellent adhesion
  • Excellent mix of appearance and protection


Physical and Chemical Properties

  • Contents : 500 ML
  • Base : Epoxy-ester
  • Colour : Aluminium silver
  • VOC content : Approximately 80 m/m %
  • Solids content : Approximately 20 m/m %
  • Heat resistant : Up to 250°C
  • Use : 1 to 2 m2 per layer, depending on object and processing method
  • Drying time : at 23°C and rel. humidity 65%
  • Dust-dry after 10 to 15 minutes
  • Touch-dry after 20 to 30 minutes
  • Hardened / resprayable after 24 hrs
  • (Depending on ambient temperature, humidity and layer thickness)
  • Storage  / Shelf life : At least 12 months in tightly closed original packaging on dry, cool and frost-free place.
  • General : Do not use below 10°C. Do not apply if threatening rain, frost or in full sunlight. Never place aerosol can on heat source.


Instructions for use

Before use, carefully read the directions on the packaging and act accordingly.

The aerosol can should be at room temperature. Ideal processing temperature 15 to 25°C. Shake the aerosol can well for 2 minutes before use and spray a sample. Distance to the surface to be treated should be approximately 25 to 30 cm. Apply PRO-Paint Zinc spray Alu Gloss in several thin layers. Before applying the next layer, shake the aerosol again. After drying, if desired a primer and a top coat can be applied. After use, clean the valve (turn aerosol upside down and press the nozzle for approximately 5 seconds). 


Properties of the PRO-Paint Zinc spray Alu Gloss 

  • Very good adhesion, provides an excellent surface for painting
  • Chemical-resistant
  • Heat resistant up to 250°C
  • Dust dry after 10 to 15 minutes
  • Touch dry after 20 to 30 minutes
  • Leave to dry for 24 hours between coats

(Figures given for information only, actual times will depend on the temperature, paint thickness, humidity etc)




Specifications of the PRO-Paint Zinc spray Alu Gloss 


Binder: epoxy-ester
Pigments: zinc and aluminium with high degree of purity
Propellant: Diméthyl ether

Health and safety

CLP labelling with three pictograms.


H222 Extremely flammable aerosol.
H229 Pressurised container: May burst if heated.
H319 Causes serious eye irritation.
H336 May cause drowsiness or dizziness.
H411 Toxic to aquatic life with long lasting effects.

picto inflammablepicto dangereux


Safety Data Sheet