Bitumen Adhesion Primer
Reference : PT 9050
Bitumen Adhesion Primer as bonding primer. It optimises bituminous plant mix work by preparing the surface to be treated properly and improving its adhesion capability. The aerosols preclude the use of tools such as brushes and blades.
Bitumen Adhesion Primer
Description of the PRO-Tech Bitumen Adhesion Primer
PRO-Tech Bitumen Adhesion Primer is a professional and fast drying primer spray for use in adhesion of hot and cold asphalt, asphalt adhesion to concrete and bonding longitudinal seams. Also well suited for processing bitumen roof products, wood underlayment panels and as protective coating for concrete, wood and iron.
The Bitumen Adhesion Primer Can be used for
REPAIRING OR REPLACING ASPHALT SURFACES
Use as a tack coat before applying cold-lay asphalt for improved adhesion.
REPLACING CAST IRON MANHOLE COVERS
Rapid drying to provide a quick and effective finish when manhole covers need to be replaced.
Applications of the PRO-Tech Bitumen Adhesion Primer
- Adhesion for hot and cold asphalt
- For processing wood underlayment panels
- Adhesion for asphalt on concrete
- Roof duct(s)
- Bonding longitudinal seams
- Roof trim
- Protective coating for concrete, wood and iron
Properties of PRO-Tech Bitumen Adhesion Primer
- Easy to use.
- Good adhesion and fast-drying.
- Can even be used for small, difficult to reach areas.
- Aerosol cans, net volume 600 ml, in boxes of 12.
Product references
- Fast drying
- Applicable to many surfaces
- Easy to use
- Makes water-repellent
Physical and Chemical Properties
- Contents : 600 ML
- Base : Bitumen
- Appearance : Black liquid / coating
- Propellant : Propane-Butane
- VOC-CH % : 78%
- VOC-EU g/l : 582 g/l
- Specific gravity (g/ml 20°C) : 0.751
- Vapour pressure at 20°C : 2.7 - 3.3 bar
- Spraying flow rate : +/- 2.5 g/sec
- Heat resistant/ temperature resistant : Tot 100°C
- Use : 2 to 3 m2 per aerosol can, depending on object and processing method.
- Drying time : At 23°C and relative humidity 65% - 30 min, (depending on ambient temperature, humidity and layer thickness).
- Storage / Shelf life : At least 12 months in a tightly closed original packaging on dry, cool and frost-free place.
- General : Do not use below 10°C. Do not apply outside if threatening rain, frost or in the full sun. Never place aerosol can on heat source.
PT 9050
Data sheet
- Product type
- technical product - other, marking - additional products
- Application area
- Synthetic, Plastic, Metal, Woods, Bitumens, Concrete
- Volume
- 600 ml
- Packaging
- Box of 12 cans
- Application domain
- Maintenance, Preparion of the supports, Mapping, tracking, picketing
Instructions for use
Before use, carefully read the instructions on the packaging and act accordingly.
The surface should be clean, dry and free of grease. Remove loose old lacquer and rust and then sand. When using outside remove all moss and algae deposits. Cover the environment. The aerosol can should be at room temperature. The ideal processing temperature is 15 to 25°C. Shake the aerosol can well for 2 minutes before use and spray a sample. Distance to the surface to be treated approximately 25 to 30 centimetres. Apply in several thin layers. Apply the next layer/ layers within30 minutes or wait until the previous layer has fully hardened. Before applying the next layer, shake the aerosol again. After use, clean the valve (turn aerosol upside down and press the nozzle for approximately 5 seconds).
DANGEROUS. FOLLOW THE PRECAUTIONS.
Health and safety
CLP labelling with a single pictogram.
DANGER
EC 649-330-00-2 NAPHTA
H222 Extremely flammable aerosol.
H229 Pressurised container: May burst if heated.
H336 May cause drowsiness or dizziness.
H372 May cause damage to organsthrough prolonged or repeated exposure.
H411 Toxic to aquatic life with long lasting effects.
EUH066 Repeated exposure may cause skin dryness or cracking.Keep out of reach of children.
Bitumen Adhesion Primer as bonding primer. It optimises bituminous plant mix work by preparing the surface to be treated properly and improving its adhesion capability. The aerosols preclude the use of tools such as brushes and blades.