Glue and Bitumen Remover
Reference : PP 0702
PRO-Tech Glue and Bitumen Remover is designed to rapidly and safely remove residues of glue, polyurethane, tar, mastic, oil, Tectyl and glue, or any other sticky substances. Is also ideal for removing grease or resin and for cleaning tools. Non-corrosive and leaves no residue after use.
Glue and Bitumen Remover
Description of the PRO-Tech Glue and Bitumen Remover
PRO-Tech Glue and bitumen remover is specially developed for the quick and safe removal of sticker glue residue, bitumen, polyurethane, tar and glue-like polyurethane, sealants, oil, tectyl, adhesive tape residue andmanyother sticky residues. Also, it’s ideally suited for cleaning tools. To be used for removing wax and fats, but also for cleaning vehicles. A very powerful cleaning agent based on natural raw materials and which is economical to use.
Specifications of the PRO-Tech Glue and Bitumen Remover
- Packaging: 500 ml
- Composition: blend of D-Limonene from orange oil, surface-active agents
- Appearance: colourless clear liquid
- Propellant: propane-butane
- VOC-EU g/l: 656 g/l
- Relative density (20°C g/ml): 0.690
- Vapour pressure at 20°C: 2.2 - 2.8 bar
- Spray flow: 0.9 g/sec
Applications of the PRO-Tech Glue and Bitumen Remover
- Oil removal
- Wax removal
- Grease removal
- Resins removal
- Tar removal
- (Sticker) glue removal
- Bitumen removal
- Applicable to steel, polyester, glass, aluminium etc.
- Paper stickers
Product references
- Versatile cleaning agent
- Citrus scent
- Very effective agent
- Based on natural raw materials
- Powerful
- Strong solvent action
- Leaves no residue
- Non-corrosive
Physical and Chemical Properties
- Contents : 500 ML
- Base : Mix of natural orange-oil d-limonene, surface-active agents
- Appearance : Clear colourless liquid
- Propellant : Propane-Butane
- VOC-CH % : 95%
- VOC-EU g/l : 656 g/l
- Specific gravity (g/ml 20°C) : 0.690
- Vapour pressure at 20°C : 2.2-2.8 bar
- Spraying flow rate : 0.9 g/sec
- Storage / Shelf life : At least 12 months in tightly closed original packaging on dry, cool and frost-free place.
- General : Do not use below 10°C. Do not use outside if threatening rain, frost or in the full sun. Never place aerosol can on heat source.
PP 0702
Data sheet
- Product type
- Cleaner
- Application area
- Plaster, Synthetic, Plastic, Metal, Woods, Bitumens, Concrete
- Volume
- 500 ml
- Packaging
- Box of 12 cans
- Application domain
- Maintenance
Instructions of use of the Glue and bitumen remover
Shake thoroughly before use. Do not use at temperatures below 10°C. Do not use outside if there is a risk of rain or frost, or in full sun. Spray the solvent cleaner onto the surface to be cleaned. Leave to act for several minutes then remove with a cloth. If marks still remain, repeat until the desired result is obtained. Do not use on rubber or polystyrene. Before using, carry out a test on a small unobtrusive area of the surface to be cleaned to verify product compatibility. Will not remove hardened paint, polyurethane coatings and similar.
DANGEROUS. FOLLOW THE PRECAUTIONS.
Health and safety
CLP labelling with three pictograms.
DANGER
(R)-P-MENTHA-1,8-DIENE
H222 Extremely flammable aerosol.
H229 Pressurised container: May burst if heated.
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H410 Very toxic to aquatic life with long lasting effects.
PRO-Tech Glue and Bitumen Remover is designed to rapidly and safely remove residues of glue, polyurethane, tar, mastic, oil, Tectyl and glue, or any other sticky substances. Is also ideal for removing grease or resin and for cleaning tools. Non-corrosive and leaves no residue after use.